Although the linked article is directed more toward shed foundations, with a few minor tweaks it becomes applicable to our case. We’ll also be referencing a more in-depth article throughout. Great question! Building a level playset foundation can be a fun DIY project by following a few simple steps. How to Level the Ground for a Swingset and Install a Foundation A couple more options might be rubber pads, rubber mulch, or simply a level grass area. Of course, the above options are not the only methods that can be used to level ground for playset. A playset pad can be installed on a sloped yard (and made level).Level ground (pad installed by experts) for swingset.Soft surface area to protect kids from hard falls.One of the safest and most durable ways to level a swingset.Here are several of the main pros for this type of playset pad. Here are 3 options: Wood Mulch Playset Pads There are several different types of playset pads that could work. Playset pads are the surest and most secure way to keep a playset level, safe, and happy playground for your kids. And that’s it!ĭon’t forget to cover the blocks with a cushion or padding for safety purposes. From there, secure the legs of the swingset to the blocks. Re-check blocks and make sure that they are level. Then, place wooden or concrete blocks in each 1’x1’ dugout. Make sure that all the 1’x1’ dugouts are at level with each other. Mark Swingset Legsįirst, mark off the locations for the swingset legs. Using blocks can also be a simple way to level your playset. Laying down woodchips, mulch, or artificial grass are some ideas. The final step is to add soft surface material to cushion any hard falls. Once the ground is leveled, install your swingset and make sure that it is anchored to the ground. Don’t forget to also level the center of the ground base as well. If the ground is not quite level, rake the dirt around a bit until each side is checked and leveled. Then, take a level and place it on top of the 2×4. You can do this by placing the 2×4 along the side of the level swingset base. Next, grab a 2×4 and double-check to make sure the ground is level. From there, level the ground where needed by removing the topsoil from the highest points. Measure the slope with a laser or string (see how to measure the slope with string here). Keep in mind, you want 6’ of extra space around the perimeter of the entire playset as a safety precaution. Measure and stake out the four corners of the swingset. To level a playset on the ground in your backyard, follow these steps: 1. We’ll dive into the details of each method: Ground Level There are a couple of ways to level a playset: (1) level the ground in your backyard, (2) use blocks, or (3) install a playset pad. How Do I Level a Playset on Uneven Ground? What is the Easiest Way to Level Uneven Ground for My Playset?.What is the Best Thing to Put on the Ground Under a Swing Set?.Do You Have to Level the Ground for A Playset?.How Much Does Leveling a Yard for a Playset Cost?.How Level does the Ground Need to be for a Playset?.What Not to Use to Level the Ground for a Playset.How to Level the Ground for a Swingset and Install a Foundation.How Do I Level a Playset on Uneven Ground?.Have a look at these ten simple rules for safer swing-set construction, and read up on the hazards of corrosion caused by pressure-treated lumber. Swing hardware should be secured with a bolt, washers, and a locking nut of some kind. Never fasten swing fittings with a lag screw, which can pull out suddenly and send a kid flying. I was shocked to see that you can buy swing hardware kits that are intended to be installed with lag screws. Use Nuts, Bolts, and Washers to Secure Swings If you go with cedar, then the screws and bolts that came with the set are fine. If you build the swing set with pressure-treated lumber, you’ll need fasteners that have a corrosion-resistant coating specifically rated to resist pressure-treated wood corrosion: stainless-steel fasteners or hot-dipped galvanized fasteners. Some manufacturers supply their kits with rust-resistant screws and bolts that are intended to be installed in cedar, not pressure-treated lumber, which is far more corrosive. If you opt for a hardware kit (without lumber), check with the manufacturer about the screws and bolts that it supplies with its fittings. There are a few things you should know to build a safe set. The place to start is with hardware kits that supply the fittings and fasteners, but not the lumber, or kits that supply finished lumber, fittings and fasteners. Swing sets are great projects for beginning DIY and mid-level DIYers.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |